Phone +86-579-89088779

中文

Planer tips

Update Time : 2021-05-06 13:44:47

Electric planer is a hand-held power tool planing by a single-phase series motor driven by a belt drive planer, with the advantages of high production efficiency, planing surface smoothness and smoothness. Widely used in housing construction, housing decoration, carpentry workshop, field woodworking and vehicles, ships, bridges and other occasions, for a variety of wood plane planing, chamfering and cutting and other operations.


Planer tips planer use safety norms Picture Keywords


 Electric planer is a hand-held power tool planing by a single-phase series motor driven by a belt drive planer, with the advantages of high production efficiency, planing surface smoothness and smoothness. Widely used in housing construction, housing decoration, carpentry workshop, field woodworking and vehicles, ships, bridges and other occasions, for a variety of wood plane planing, chamfering and cutting and other operations.


Electric planer is widely used in home construction, housing decoration, carpentry workshop, field carpentry and vehicles, ships, bridge construction and other occasions, for a variety of wood planing, chamfering and cutting and other operations. Planer has a direct drive and indirect drive two structures. Direct drive is planing knife mounted directly on the motor output shaft, the indirect drive is the output shaft of the motor driven by the nylon drive shaft.


Planer by the motor, the knife cavity structure, planing depth adjustment mechanism, handle, switch and can not reconnect the plug and other components. This series of planer with double insulation structure. Planer shell, the handle plastic injection molding into one, plastic shell as an additional insulation core of the stator and rotor core to the additional insulation to form double insulation.


Knife cavity structure has upper and lower two layers, the upper for the chip chamber by the motor cooling fan wind chip removal. Planing depth adjustment mechanism by the adjustment handle, anti-loose spring, the front plate and other components, twist the adjustment handle, so that the front floor up and down to adjust the planing depth. The output shaft of the motor drives the nylon belt to drive the planer on the cutter shaft for planing work. Power cord with double heart sheath soft cable, and double column rubber plug into a whole can not be reconnected plug.


Before using safety regulations to prepare


1, the workpiece must be jacketed in the fixture or workbench, clamping the workpiece platen plate not allowed to grow, not allowed to stand in the maximum travel of the machine. Do not extend the tool too long, should be securely fastened.


2, when correcting the workpiece, it is forbidden to use the metal object to knock or use the tool holder to push the workpiece.


3, the width of the workpiece beyond the width of the arm planer processing, the center of gravity on the work table center of gravity offset should not be greater than one-fourth of the width of the table.


4, adjust the stroke should make the tool does not touch the workpiece, shake with the handle for the entire stroke test, ram adjustment should be locked and shake the handle removed at any time, so as not to fall hurt.


5, gantry planer bed or work piece extended too long, should be set up guard railings, banned in the railing through pedestrian or stacking items.


6, planer planing big workpiece before planing, should first check the workpiece and the gantry post, the gap between the knife holder, and check the workpiece height limiter installation is properly installed.


7, gantry planing worktops and bed and knife stand is prohibited, storage tools and other items. Operators may not cross the table.


8, the role of the shaper handle on the force, the horizontal movement of the table should not exceed 8kg, up and down movement, it should not exceed 10kg.


9, the workpiece handling, turn their attention should be sharp edge, burr cut hands.


Precautions in operation


1, within the planing trip range, before and after not allowed to stand, not allowed to head, hand reach the taizu observation cutting parts and tools, did not stop the front, not allowed to measure the workpiece or remove chips.


2, eat the amount of knife and the amount of feed to be appropriate before the knife should make the planer slowly approaching the workpiece.


3, planer must first run back after eating knife or feed, planing in progress to make planer stop running, you should first planer from the workpiece.


4, operating speed and stability, the sliding bearing temperature should not exceed 60 ℃ rolling bearing temperature should not exceed 80 ℃.


5, gantry planer table stroke adjustment, you must shut down, the maximum stroke at both ends of the margin shall not be less than 0.45m.


6, often check the tool, the workpiece is fixed and the operation of the various parts of the machine is normal.


Shutdown precautions


1, if found in the work ram temperature is too high, reversing impact sound or stroke vibration abnormal sound or sudden stop and other undesirable conditions, should immediately cut off the power and exit the tool for inspection, adjustment, repair and so on.


2, after the shutdown, the bull head ram or gantry plane countertops, knife back to the required position. Use tips to be careful when using the safety (wood with nails and other metal objects, you need to remove to use.) Planing material should be depending on the length of the wood, using different postures, one hand down the front end when feeding, the other hand care Live wood back end, long material as far back as care, to maintain a stable wood, to ensure that planed surface and planer platform exactly match, not Alice, or scraped out of the surface will be uneven. Planer after the back of a smooth forward, The hand moves forward as the timber moves backwards, preferably just above the planing edge to prevent jerkiness. When the planing comes to an end, the front hand moves forward with the timber and presses downwards without exceeding the platform, with the rear hand pressing at the end Push forward, if the long material, one hand can not hold, the front of the best someone pick one, so as to ensure the planing of timber planing.Planing the shaver is generally used for roughing, and with the belt machine.


Previous:No

Next:The use of electric circular saw

CONTACT US

OUR ADDRESS

NO.2 HEHUA ROAD BAIHUASHAN DEVELOPMENT ZONE BAIYANG STREET WUYI JINHUA ZHEJIANG

+86-579-89088779

ls003@longstool.com

www.longstool.com